|
delta loop
|
| 163SD195 Danny |
Posted on 23-06-2017 13:48
|
Junior Member
Posts: 26
Joined: 27.12.14
|
been thinking about building a deta loop for 27mhz, does anyone have the measurements for this project please. |
| |
|
|
| 163IR010 |
Posted on 21-07-2017 17:16
|
Newbie
Posts: 1
Joined: 08.02.16
|
300 over frequency, plus 75 ohm tuning stub about 2 mtrs |
| |
|
|
| 21SD104 |
Posted on 22-07-2017 08:38
|
Newbie
Posts: 5
Joined: 19.07.17
|
http://dl5dbm.darc.de/d11m_e.pdf
21SD104
21sd104@gmail.com
|
| |
|
|
| 163SD195 Danny |
Posted on 24-07-2017 18:21
|
Junior Member
Posts: 26
Joined: 27.12.14
|
Many thanks Albert m8 |
| |
|
|
| 163SD195 Danny |
Posted on 24-07-2017 18:22
|
Junior Member
Posts: 26
Joined: 27.12.14
|
Thank youTommie . |
| |
|
|
| 31hs867 |
Posted on 28-08-2017 17:49
|
Newbie
Posts: 5
Joined: 16.02.16
|
Works fine, very good reception. |
| |
|
|
| Bokyking |
Posted on 30-04-2018 17:36
|
Newbie
Posts: 1
Joined: 03.02.18
|
I hope that one day I will get one 
<IFRAME> src="http://www.dxproof.com/iframeqrz.asp?iduser=1688" width='468px' height='60px' scrolling='no' frameborder='0' marginwidth='0' marginheight='0' ></IFRAME>
|
| |
|
|
| cplkaos |
Posted on 18-05-2019 10:18
|
Newbie
Posts: 1
Joined: 04.05.16
|
I have homwbrewed my 2 Element Delta Loop......
http://www.macoantennas.net/files/Assembly_V-Quad.pdf
That there is your best friend. Works for the one element too.
Stub is 1.8m 75ohm coax wrapped around a cola bottle 7 times. Works perfect for me. |
| |
|
|
| tonester |
Posted on 04-07-2019 19:57
|
Junior Member
Posts: 14
Joined: 31.03.19
|
cuts the noise by2/3 s points well it did here....I used 75ohm satelitte 1.1 meters £1 and meter I think and 37.73 ft of wire....sorry I mixed the measurements but its how I remember it... vertical was a found fishing rod and horizontals were two canes tie wrapped to the center and together..... cost including the wire about £7 cheap to make and test...to get the lengths correct at least.... |
| |
|
|
| 1da006 |
Posted on 19-06-2022 06:09
|
Newbie
Posts: 4
Joined: 30.07.20
|
Se fatta a 37° non occorre adattatore di impedenza, risulta a 50 Ohm, Collegata direttamente al cavo di discesa. Ros 1:01 su quasi tutta la banda.
73s |
| |
|
|
| 2EK925 |
Posted on 19-11-2024 00:57
|
Newbie
Posts: 1
Joined: 19.12.22
|
163SD195 Danny wrote:
been thinking about building a deta loop for 27mhz, does anyone have the measurements for this project please.
Ron Bruckman
|
| |
|
